In this article down the page you can get lots of good quality content all about Installing A Bathtub.
Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is conveniently accessible, the project can relocate speedily; if you have to open up a wall surface to eliminate the old bathtub as well as position the new bath tub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will need an assistant to leave the old bathtub as well as embeded in the new one. See to it you have certified on your own for the job and also fit trying it. Rather than employing a specialist to take control of a halfway-completed project, it is better to take into consideration using one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your washroom if you have actually already gotten a brand-new bathtub and don't require to change the plan of your previous water pipes.
Your devices and also material list ought to make up the following:
Getting ready for the Installment
To start with, the sustaining frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for position. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bathtub until the spirit level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the water system and check all joints and also brand-new pipework for leaks and also tighten them if essential. Load the tub and likewise check the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, take care of the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait till the tub has actually been used at the very least once as this will resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washers are in location in between the tap and also the sink. Protect the tap in position with the supplier offered backnut. As soon as the tap is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous type must be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack a stiff seal, causing the water to permeate the wall surface in between the bath and also the tiling, bring about difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can break relatively very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very involved in Installing A Bathtub and I'm hoping you enjoyed the entire piece. Kindly take a moment to distribute this blog post if you liked it. I love reading our article about How to Install a Bathtub Yourself.
Facing a flood? Call us!